![]() Hertz rental vehicles are PlatePass® enabled for use on covered tollways. The toll road system will automatically read the license plate of the vehicle. ![]() ![]() If your vehicle is not equipped with a transponder, simply drive through the toll lane. If the transponder malfunctions, or is not present, your rental vehicle will still be enrolled in PlatePass® if you incur tolls without using a personal transponder or other approved payment method.įor Video regions: The toll authority’s technology obtains a photo of the vehicle’s license plate, which allows the toll authority to assess tolls to that vehicle.įor Transponder regions: To use PlatePass®, slide open the gray transponder box behind the rearview mirror (if available), so that the toll agency can read the transponder. The transponder communicates with the tollway using radio frequency technology, collecting information from the transponder to pay the toll. Ability to use all-electronic tollways and bridges, without using a personal transponder or paying the toll authority directlyįor Transponder regions: In E-ZPass and I-PASS regions, your rental vehicle may be equipped with a transponder.PlatePass® is an electronic toll payment solution that enables you to use covered cashless toll collection lanes or all-electronic tollways, without the use of a personal transponder or paying the toll authority directly. and Puerto Rico.įor a complete listing of participating toll roads and state maps, please visit /locations. You’ll be able to use PlatePass® throughout the U.S. PlatePass® allows you to use cashless lanes or all-electronic tollways without using a personal transponder or paying the toll authority directly. Bolt the E-ZPass tag to the cab roof securely.Experience the speed and convenience of PlatePass®.within 1' of any trailers or other metal objects.Ī plastic or fiberglass air dam or spoiler may cover the E-ZPass tag, provided the cover does not have any metallic paint or metal foil decals on it.behind horns, lights or other metal objects.on the sloping surface of a cab or roof - the bottom of the tag assembly must be parallel to the road.within 2' of any radio transmitting antennas.It should be on the roof of the vehicle, on the centerline a minimum of 3" from the front of the cab roof. Locate the correct installation position for your E-ZPass roof-mount tag. Please note: Your E-ZPass license plate tag should be attached to the center of the front bumper, even if your license plate is in a different location.Tighten the bolts securely, but do not over tighten. Fasten your E-ZPass tag to the front license plate using the existing top mounting bolts and the knock-out holes at the bottom of the E-ZPass tag, so you do not cover the state name on your license plate.This side should face inward to your vehicle. It will have the sticker with the Maine Turnpike Logo. Identify the flat side of your E-ZPass tag.You may order additional mounting strips by calling E-ZPass Customer Service atġ-888-MTA-PASS (1-88), Monday through Friday, 8:00 AM to 6:00 PM An extra set of mounting strips was provided with your E-ZPass order. Please note: Do not try to remove the mounting strips from your windshield and reuse them.Your E-ZPass tag may be removed by gently lifting one corner of the tag to separate the adhesive strips.Place the tag in the correct position and press firmly against the glass for 15 seconds to achieve a good bond. Turn the tag right side up facing you.Without removing the second set of adhesive strips from the tag, carefully remove the protective backing from the mounting strips on the rear of the tag. There are four adhesive strips: two are permanently mounted to the tag, and two are for mounting to the windshield.If your vehicle has tinted glass, make sure the device is at least 1 inch below the tinted section of glass. Locate the correct position for the tag - the upper center portion of your windshield behind the rearview mirror, at least 1 inch to the right of the mirror and at least 1 inch below the top edge of the windshield.This side faces the interior of the vehicle with the arrows on the tag pointing toward the roof. Identify the front face of your E-ZPass tag (it will have the label with the Maine Turnpike Logo and the tag serial number).Clean and dry the inside of your windshield around the rearview mirror.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |